UF Membrane Module 6 inch PVDF Ultrafiltration Membrane Module UFf160 Grinding Waste Water Treatment

Short Description:

● Bangmo PVDF material has good pollution resistance, oxidation resistance, and is easy to clean;

● Bangmo PVDF material has high flux, stable output and long service life;

● Easy control, continuous operation, remote control;

● Online gas-water washing, good flux recovery;

● Small footprint, compact structure, modular design is applicable to different operation capacity;

● Super low pressure operation, energy saving;

● Industrial chemicals can be used for membrane washing so as to save costs;

● Good output quality, high recovery rate, water source saving;

Product Detail

Product Tags

Product Overview

UFf160 capillary hollow fiber membrane is high polymer material, which will not have any phase change. Modified PVDF material, which is adopted on this product, has good permeable rate, good mechanical properties, good chemical resistance and pollution resistance. MWCO is 200K Dalton, membrane ID/OD is 0.8mm/1.3mm, filtering type is outside-in.


  • Drinking water treatment of tap water, surface water, well water and river water.
  • Pretreatment of RO.
  • Treatment, recycle and reuse of industrial waste water.

Filtration Performance

This product is proven to have below filtering effects according to the service conditions of different water sources:

Ingredient Effect
SS, Particles > 1μm Removal Rate ≥ 99%
SDI ≤ 3
Bacteria, Viruses > 4 log
Turbidity < 1NTU
TOC Removal Rate: 0-25%

*Above data is obtained under the condition that feeding water turbidity is < 25NTU.

Product Parameters


Technical Parameters:

Filtering Type Outside-in
Membrane Material Modified PVDF
MWCO 200K Dalton
Membrane Area 40m2
Membrane ID/OD 0.8mm/1.3mm
Dimensions Φ160mm*1810mm
Connector Size DN40 Union Joint

Application Data:

Pure Water Flux 8,000L/H (0.15MPa, 25℃)
Designed Flux 40-120L/m2.hr (0.15MPa, 25℃)
Suggested Working Pressure ≤ 0.2MPa
Maximum Transmembrane Pressure 0.15MPa
Maximum Backwashing Pressure 0.15MPa
Air Washing Volume 0.1-0.15N m3/m2 .hr
Air Washing Pressure ≤ 0.1MPa
Maximum Working Temperature 45℃
PH Range Working: 4-10; Washing: 2-12
Operating Mode Cross Flow

Feeding Water Requirements:
Before feeding water, a security filter < 50 μm should be set to prevent blockage caused by large particles in raw water.

Turbidity ≤ 25NTU
Oil & Grease ≤ 2mg/L
SS ≤ 20mg/L
Total Iron ≤ 1mg/L
Continuous Residual Chlorine ≤ 5ppm
COD Suggested ≤ 500mg/L

*Material of UF membrane is polymer organic plastic, there must not be any organic solvents in raw water.

Operating Parameters:

Backwashing Flow Rate 100-150L/m2.hr
Backwashing Frequency Every 30-60min.
Backwashing Duration 30-60s
CEB Frequency 0-4 times per day
CEB Duration 5-10min.
CIP Frequency Every 1-3 months
Washing Chemicals:
Sterilization 15ppm Sodium Hypochlorite
Organic Pollution Washing 0.2% Sodium Hypochlorite + 0.1% Sodium Hydroxide
Inorganic Pollution Washing 1-2% Citric Acid/0.2% Hydrochloric Acid

Component Material:

Component Material
Membrane Modified PVDF
Sealing Epoxy Resins
Housing UPVC

  • Previous:
  • Next:

  • Write your message here and send it to us